Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 32
Like Tree1Likes

Thread: Is anyone using Okudo Suita for finishing hone?

  1. #21
    I Bleed Slurry Disburden's Avatar
    Join Date
    Feb 2009
    Location
    Carmel, NY
    Posts
    2,458
    Thanked: 545

    Default

    Suita means there are pockets of air in the stone they can clog easily?

  2. #22
    I used Nakayamas for my house mainaman's Avatar
    Join Date
    Aug 2009
    Location
    Des Moines
    Posts
    8,664
    Thanked: 2591
    Blog Entries
    1

    Default

    Quote Originally Posted by Disburden View Post
    Suita means there are pockets of air in the stone they can clog easily?
    yes air bubbles, however there are suita stones with no Su but those are rare or so I have been told.
    Stefan

  3. The Following User Says Thank You to mainaman For This Useful Post:

    Disburden (10-29-2010)

  4. #23
    Member
    Join Date
    Oct 2010
    Posts
    58
    Thanked: 9

    Default

    Are you saying not using another small Okuda Suita stone as slurry stone as well?

    JSZ

  5. #24
    I used Nakayamas for my house mainaman's Avatar
    Join Date
    Aug 2009
    Location
    Des Moines
    Posts
    8,664
    Thanked: 2591
    Blog Entries
    1

    Default

    Quote Originally Posted by UrsaMaior View Post
    Are you saying not using another small Okuda Suita stone as slurry stone as well?

    JSZ
    If you are going to be using a piece of your own stone you will be fine. If the small stone is from another Okudo, and has grit that is not finer or the same as your stone then you will not get the best result.
    IMHO safest way to go is a diamond plate.
    Stefan

  6. #25
    Member
    Join Date
    Oct 2010
    Posts
    58
    Thanked: 9

    Default

    Yes ,

    I like the idea of diamond plate but was told that it might make scratches as well.

    To be honest I am thinking about cutting a small piece of and make a slurry stone .
    After all the stone is big enough to do the job ( honing razors) and at the end I will have a set up like we can see with vintage Escher in the box with the slurry stone.

    JSZ
    Last edited by UrsaMaior; 10-30-2010 at 04:13 AM. Reason: spellig.........

  7. #26
    Senior Member
    Join Date
    Jan 2008
    Location
    Northern California
    Posts
    1,301
    Thanked: 267

    Default

    I remember reading a post somewhere that if you make a slurry from a suita stone it is possible that chips will lodge in the holes and cause problems????

    Richard

  8. #27
    alx
    alx is offline
    Senior Member alx's Avatar
    Join Date
    Aug 2009
    Location
    Sonoma, California
    Posts
    418
    Thanked: 405

    Default

    Hello JSZ
    I was a little surprised to read that you might cut a piece of your Okudo stone to make up a slurry stone. There is a very good chance that in the near future you will regret doing so. These stones although dull, are gems in their own class and you should feel lucky to have found such a large stone to begin with. Cutting a stone is like cutting a piece of rope, you can never put it back together to be as strong or as long.

    If you are really looking for a slurry on your stone that is made up of the stone, try sharpening a chisel or a kitchen knife on the stone with some heavy strokes, it will work up a slurry in with just a few strokes. Also you might just buy a 1 x 4 inch DMT diamond pocket stone for just a few bucks and just raise a bit of a slurry at a time on the stone where you are going to hone at.

    In the long run though, in order to maintain the flatness of your beauty you will want to invest in an 8 x 3 diamond plate which can serve many purposes in you growing collection of razors and hones. I use one to to take out a deep frown in an edge, and then just rinse it off and use it to flatten a stone. Think of all of the glowing compliments you got about this stone right off the bat, please do not cut it up. regards, Alex

  9. #28
    Senior Member blabbermouth niftyshaving's Avatar
    Join Date
    Oct 2009
    Location
    Silicon Valley, CA, USA
    Posts
    3,157
    Thanked: 852

    Default

    Quote Originally Posted by UrsaMaior View Post
    Yes ,

    I like the idea of diamond plate but was told that it might make scratches as well.

    To be honest I am thinking about cutting a small piece of and make a slurry stone .
    After all the stone is big enough to do the job ( honing razors) and at the end I will have a set up like we can see with vintage Escher in the box with the slurry stone.

    JSZ
    While it is your hone to do as will please do not cut a bit off.

    A small hard white Arkansas hone or a small DMT ceramic hone can be used
    to raise a slurry or freshen the surface.

  10. #29
    The Great & Powerful Oz onimaru55's Avatar
    Join Date
    May 2008
    Location
    Bodalla, NSW
    Posts
    15,626
    Thanked: 3749

    Default

    Quote Originally Posted by UrsaMaior View Post
    Yes ,

    I like the idea of diamond plate but was told that it might make scratches as well.

    To be honest I am thinking about cutting a small piece of and make a slurry stone .
    After all the stone is big enough to do the job ( honing razors) and at the end I will have a set up like we can see with vintage Escher in the box with the slurry stone.

    JSZ
    Don't worry about scratches. When the plate breaks in they are very fine, even from a DMT C which is rated at 325 grit. In fact the slurry itself negates the depth of any scratches.
    I use an Atoma 1200 as recommended by So from Japan Tool.
    Another bonus is that you are partially lapping your stone each time you make slurry.
    The white gleam of swords, not the black ink of books, clears doubts and uncertainties and bleak outlooks.

  11. #30
    Senior Member blabbermouth
    Join Date
    Jul 2010
    Location
    Portland, OR
    Posts
    2,697
    Thanked: 830
    Blog Entries
    1

    Default Oxygen needed here!

    I have a nose bleed from seeing the prices

    The part that makes it tough is those comments about the edge being smoother. I've gotta stop looking at these threads on Jnats. I still don't know what guys do about all the kanji characters stamped on the surface. Are these erased with the first use? Dang, I figure they must be about $200 each!

    I hope to experience a jnat edge soon, courtesy of the honorable Riooso. 'Can't wait, but with some fear and trepidation. If it's that good, I'll be downtown with a sign: will work for jnats. Gulp.

  12. The Following User Says Thank You to pinklather For This Useful Post:

    alx (10-31-2010)

Page 3 of 4 FirstFirst 1234 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •