Results 1 to 10 of 49
Like Tree38Likes

Thread: First 3 Pin razor restore - Dubl Duck Goldedge

Threaded View

RickyBeeroun222 First 3 Pin razor restore -... 12-28-2013, 05:51 AM
JReed Is that gold plate around the... 12-28-2013, 06:05 AM
ne0nblakk Looks like a nice razor. ... 12-28-2013, 08:17 AM
RickyBeeroun222 @JReed It looks like it is... 12-28-2013, 08:48 AM
mrsell63 Member mycarver can gold... 12-28-2013, 08:54 AM
Barberologist Nice pickup Ricky. Those... 01-05-2014, 08:48 AM
RickyBeeroun222 It's been a while since my... 01-13-2014, 10:14 AM
Chevhead It's looking good bro! ... 01-13-2014, 10:24 AM
RickyBeeroun222 Thanks Ed. I am making sure... 01-13-2014, 10:37 AM
RickyBeeroun222 Had some more time to work on... 01-18-2014, 08:39 AM
Chevhead That is looking AWESOME! :tu 01-18-2014, 10:51 AM
RickyBeeroun222 Ed, Thanks for the... 01-19-2014, 03:18 AM
Chevhead I don't know how much... 01-19-2014, 03:30 AM
10Pups Those scales are layered. The... 01-19-2014, 03:37 AM
RickyBeeroun222 Tried the over bend method... 01-20-2014, 10:05 AM
RickyBeeroun222 i decided to live with this... 01-23-2014, 12:16 AM
Chevhead Once you test pin it you can... 01-23-2014, 12:46 AM
RickyBeeroun222 Having some difficulty... 01-25-2014, 01:35 AM
Chevhead If you decide to remove the... 01-25-2014, 02:13 AM
RickyBeeroun222 @Ed Sent email again ==... 01-25-2014, 06:01 AM
Chevhead Yep got it! 01-25-2014, 06:55 AM
Havachat45 Lovely work Rick - can't wait... 01-25-2014, 08:10 AM
RickyBeeroun222 Tried a mock up today ---... 01-26-2014, 07:23 AM
RickyBeeroun222 Passion fingers happened -... 01-27-2014, 10:22 PM
tintin Bummer! I can feel your pain.... 01-27-2014, 10:36 PM
Chevhead Yikes! Good news us you can... 01-28-2014, 12:01 AM
RickyBeeroun222 I have some experience with... 01-28-2014, 12:03 PM
Chevhead Check your messages bro.... 01-28-2014, 01:17 PM
RickyBeeroun222 Bit the bullet and ordered a... 02-02-2014, 12:09 AM
Chevhead See what you like the best... 02-02-2014, 05:32 AM
RickyBeeroun222 Getting started on some new... 02-22-2014, 12:23 PM
RickyBeeroun222 Where did the time go, I... 05-18-2014, 10:44 AM
tintin can't wait to see how it... 05-18-2014, 11:35 AM
Chevhead ALWAYS polish the bolsters... 05-18-2014, 11:40 AM
RickyBeeroun222 @tintin I'm working on... 05-20-2014, 09:17 AM
RickyBeeroun222 Finished at last ... after... 06-07-2014, 04:30 AM
tintin Hey, good job. think of all... 06-07-2014, 11:05 AM
carrolljc What did you use to glue the... 06-07-2014, 07:16 PM
RickyBeeroun222 @tintin Thank you for your... 06-08-2014, 07:21 AM
Chevhead Looks pretty good bro... :tu 06-08-2014, 11:57 AM
  1. 01-19-2014, 03:30 AM #12
    Chevhead is offline
    Senior Member blabbermouth Chevhead's Avatar
    Join Date
    Feb 2013
    Location
    Upstate, New York
    Posts
    2,751
    Thanked: 708
    Blog Entries
    4

    Default

    I don't know how much straighter you want them bro... They look pretty darn straight to me!

    I am thinking maybe the wood as a backer had too much "give" to it?

    I straightened mine with a HEAT GUN.

    Held the scale in my hand and heated it just enough so as not to burn my hand then I layed them on the table of my bench scroll saw and pressed down with my fingers.

    It was COLD out so the metal was quite cold also. It only took about 5 minutes for each scale to get straight...or as straight as I liked them.

    As for the pivot area, I might try putting some Super Glue there to fill in the cracks and then sanding it down flat. You have thrust washers going there anyways so I do believe that it "should" provide enough stability for this. Maybe gluing the washers there could work also?
    dexter90723 likes this.

    Ed
    Reply With Quote Reply With Quote

  2. The Following User Says Thank You to Chevhead For This Useful Post:

    RickyBeeroun222 (01-19-2014)
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules