Results 1 to 8 of 8
Like Tree32Likes
  • 23 Post By Euclid440
  • 2 Post By cudarunner
  • 1 Post By randydance062449
  • 1 Post By Steel
  • 1 Post By Theoman
  • 1 Post By JellyJar
  • 3 Post By outback

Thread: How I made (PETE) Clear Plastic Thrust Washers

  1. #1
    Senior Member blabbermouth
    Join Date
    Apr 2012
    Location
    Diamond Bar, CA
    Posts
    6,553
    Thanked: 3215

    Default How I made (PETE) Clear Plastic Thrust Washers

    (PETE) Clear Plastic Thrust Washers

    I recently posted a thread about a very nice Satin Wedge Double Duck I pick up for a song, with no Cell Rot and almost no hone wear.
    Original scales with brass thrust washers.

    Name:  1 orig washers.jpg
Views: 300
Size:  52.4 KBName:  2 pivot.jpg
Views: 285
Size:  54.5 KB

    One of the things I don’t like about Ducks with transparent scales is the brass thrust washers at the pivot. They look ok new, but once they start to tarnish the pivot looks dirty. So, I made new clear plastic thrust washers from a(PETE), plastic water bottle with a leather hand punch.
    Some failed attempts at centering the hole. Note washer compared to originals.

    Name:  3 failed.jpg
Views: 262
Size:  45.0 KBName:  4.jpg
Views: 237
Size:  65.4 KB

    They came out fine, just a bit smaller than stock and about as thin and are almost invisible. The pivot action is nice and smooth. I also domed collars just a bit larger, to hide the indents and slight cracking where the old collars bit into the brittle celluloid.

    I used a rotary leather punch at the largest die, just under a ¼ inch. The problem I had was, centering the hole as the scales were clear and anything but centered would show.

    First, I punched out a dozen discs. I put 2 layers of electrical tape on the brass anvil and punch a hole in the tape and removed the “hole” leaving the surrounding tape.
    Electrical Tape centering hole.

    Name:  5 tape.jpg
Views: 246
Size:  19.9 KBName:  6 in hole.jpg
Views: 240
Size:  24.5 KB

    Place a disc in the hole in the tape. The little bit of tape on the perimeter of the punched hole, helps hold the disc in place. Now at the smallest punch setting about a 1/6th in. center and punch the center hole. All the dies use the same center point.

    You may have to adjust as these are not high-quality punches, but you can adjust by eye a bit. I cranked out a dozen in 5 minutes. And plan on using them with translucent and light-colored scales in place of brass.

    Pinned and finished, note how invisible the PETE plastic washer are.


    Name:  7.jpg
Views: 235
Size:  51.1 KBName:  8.jpg
Views: 245
Size:  58.6 KBName:  9.jpg
Views: 239
Size:  81.9 KB

  2. The Following 13 Users Say Thank You to Euclid440 For This Useful Post:

    BobH (03-18-2019), Diboll (03-18-2019), Geezer (03-18-2019), JellyJar (03-19-2019), JP5 (03-19-2019), JSmith1983 (03-19-2019), markbignosekelly (03-18-2019), Montgomery (09-21-2019), outback (03-19-2019), randydance062449 (03-18-2019), spazola (03-18-2019), Theoman (03-18-2019), tintin (03-18-2019)

  3. #2
    'with that said' cudarunner's Avatar
    Join Date
    Aug 2010
    Location
    Walla Walla in WA State USA
    Posts
    11,151
    Thanked: 4230

    Default

    Thanks for the tutorial, very helpful.

    If you wanted a slightly larger OD this set goes to 5/16". I found them reasonably priced and so far have worked well on leather and webbing so I would presume that they would work just fine on the plastic.

    https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
    Geezer and Euclid440 like this.
    Our house is as Neil left it- an Aladdin’s cave of 'stuff'.

    Kim X

  4. The Following 2 Users Say Thank You to cudarunner For This Useful Post:

    Euclid440 (03-18-2019), Geezer (03-18-2019)

  5. #3
    Hones & Honing randydance062449's Avatar
    Join Date
    May 2005
    Location
    Saint Paul, Minnesota, United States
    Posts
    7,971
    Thanked: 2202
    Blog Entries
    1

    Default

    I admire your ingenuity and taking the time to share this.
    I have some Ducks that I will be using this on.
    Euclid440 likes this.
    Randolph Tuttle, a SRP Mentor for residents of Minnesota & western Wisconsin

  6. #4
    Senior Member blabbermouth Steel's Avatar
    Join Date
    Nov 2013
    Posts
    2,321
    Thanked: 498

    Default

    That looks MUCH cleaner and better.
    Euclid440 likes this.
    What a curse be a dull razor; what a prideful comfort a sharp one

  7. The Following User Says Thank You to Steel For This Useful Post:

    Euclid440 (03-18-2019)

  8. #5
    Senior Member
    Join Date
    Apr 2018
    Location
    Vienna Austria
    Posts
    337
    Thanked: 98

    Default

    Freaking genius in my opinion.
    Euclid440 likes this.

  9. The Following User Says Thank You to Theoman For This Useful Post:

    Euclid440 (03-18-2019)

  10. #6
    Senior Member JellyJar's Avatar
    Join Date
    Feb 2019
    Location
    Salida, CA
    Posts
    600
    Thanked: 94

    Default

    Great idea! Another possible solution to your centering problem could be using double sided tape (scotch type) to stick the original washer to the plastic. Then use the original as a guide/template for the punch. After punching you could cut around the outside of the brass washer with your choice of sharp implements (scissors/x-acto knife etc). Not sure if the punch sizes would fit the original well enough to be a good alignment aid. Just a thought.
    Euclid440 likes this.

  11. #7
    JP5
    JP5 is offline
    Senior Member blabbermouth JP5's Avatar
    Join Date
    Feb 2015
    Location
    Duluth, GA - Atlanta OTP North
    Posts
    2,546
    Thanked: 315
    Blog Entries
    1

    Default

    This is a great idea, thanks for posting.
    - Joshua

  12. The Following User Says Thank You to JP5 For This Useful Post:

    Euclid440 (03-19-2019)

  13. #8
    Senior Member blabbermouth outback's Avatar
    Join Date
    Mar 2015
    Location
    Akron, Ohio
    Posts
    11,924
    Thanked: 4300

    Default

    Sweet idea, Marty. Daddy like.
    Mike

  14. The Following User Says Thank You to outback For This Useful Post:

    Euclid440 (03-19-2019)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •