Page 1 of 5 12345 LastLast
Results 1 to 10 of 43
Like Tree51Likes

Thread: Cleaned Up My Otto Deutsch Hans With My Dremel & Mothers Chrome Polish

  1. #1
    Senior Member blabbermouth engine46's Avatar
    Join Date
    Feb 2014
    Location
    Republic of Texas
    Posts
    7,810
    Thanked: 1744
    Blog Entries
    2

    Default Cleaned Up My Otto Deutsch Hans With My Dremel & Mothers Chrome Polish

    Here is how I cleaned up my Otto Deutsch Hans I recently got off eBay. The fist pic is what it looked like when I got it.Name:  IMG_7240.jpg
Views: 570
Size:  39.1 KB
    I then took it to my kitchen sink where I did the work to it. I usually take the razor apart but this one i didn't, I just carefully worked around the scales. If I leave the scales on I usually put tape on them to protect them but I wanted you to get a better picture of how I did this. I have had several members on here say that they would never use a Dremel on a straight razor but I learned from Lynn's dvd on how to use it the correct way on one. I have not screwed up yet......knock on wood. I cannot stress enough that you must be very careful if using a Dremel on a straight razor or it can be disastrous. You must alway watch which way the tool is spinning or it may grab your blade & crack or chip it. I applied Maas Metal Polish to the blade & went to work with my Dremel. I start polishing.
    Name:  IMG_7396.jpg
Views: 573
Size:  56.4 KBName:  IMG_7399.jpg
Views: 662
Size:  46.3 KB
    The same applies to the shoulder except I am polishing perpendicular to the blade but with the polishing wheel spinning away from the blade to prevent any damage as you can see in the photo. I then carefully polish the tang & tail. I also carefully polish spine as well. If it starts to get warm, it is a good idea to let it cool before you begin again.
    Name:  IMG_7400.jpg
Views: 493
Size:  52.3 KBName:  IMG_7401.jpg
Views: 520
Size:  46.5 KBName:  IMG_7406.jpg
Views: 465
Size:  42.6 KBName:  IMG_7409.jpg
Views: 452
Size:  35.3 KB
    The next photo is of the name on the scales after just wiping them off.
    Name:  IMG_7414.jpg
Views: 483
Size:  38.4 KB
    I then used Mothers Chrome Polish on the scales.Name:  IMG_7416.jpg
Views: 560
Size:  31.0 KBName:  IMG_7417.jpg
Views: 482
Size:  28.9 KBName:  IMG_7418.jpg
Views: 486
Size:  37.8 KB
    There you have it, nice & polished!Name:  IMG_7419.jpg
Views: 496
Size:  47.9 KBName:  IMG_7421.jpg
Views: 491
Size:  27.1 KB
    If you look close enough, the scales weren't black like I originally thought. The dull spots are glare, not smudge from my fingers. After polishing them, you can barely see the blade through the scales when the blade is closed. They're dark green as always!
    Last edited by engine46; 12-05-2014 at 01:59 AM.
    mrsell63, lz6, Geezer and 23 others like this.

  2. The Following 2 Users Say Thank You to engine46 For This Useful Post:

    Dzanda (12-04-2014), sharptonn (12-05-2014)

  3. #2
    Senior Member
    Join Date
    Oct 2014
    Location
    Denver, CO
    Posts
    207
    Thanked: 11

    Default

    That's a beaut!
    engine46 likes this.

  4. The Following User Says Thank You to Pringr For This Useful Post:

    engine46 (12-04-2014)

  5. #3
    Member
    Join Date
    May 2014
    Location
    WV
    Posts
    61
    Thanked: 4

    Default

    Wow, great job!
    engine46 likes this.

  6. The Following User Says Thank You to stevekolt For This Useful Post:

    engine46 (12-04-2014)

  7. #4
    Senior Member Wirm's Avatar
    Join Date
    Feb 2014
    Location
    West Virginia
    Posts
    605
    Thanked: 284

    Default

    Nice work 46, I am afraid of my dremel !
    engine46 likes this.
    "It is easier keeping a razor honed than honing a razor."

  8. The Following User Says Thank You to Wirm For This Useful Post:

    engine46 (12-04-2014)

  9. #5
    Senior Member blabbermouth engine46's Avatar
    Join Date
    Feb 2014
    Location
    Republic of Texas
    Posts
    7,810
    Thanked: 1744
    Blog Entries
    2

    Default

    Quote Originally Posted by Wirm View Post
    Nice work 46, I am afraid of my dremel !
    That's good. You need to be afraid of it but you can also do the job & do it right if you use it correctly. Like i said, I couldn't stress enough on how important it is to make sure if you do this to make sure the tool is spinning in the right direction. You can be successful by doing so. It took me about an hour to do this or maybe less. I also have some electrical tape wrapped around the shank of the polishing fixture just in case it makes contact with any metal parts.
    Last edited by engine46; 12-04-2014 at 07:36 PM.
    Geezer likes this.

  10. #6
    Senior Member blabbermouth nicknbleeding's Avatar
    Join Date
    Oct 2009
    Location
    Springfield,Ma
    Posts
    3,145
    Thanked: 1285

    Default

    Damn that came out great.
    engine46 likes this.

  11. The Following User Says Thank You to nicknbleeding For This Useful Post:

    engine46 (12-04-2014)

  12. #7
    Senior Member blabbermouth Substance's Avatar
    Join Date
    Jun 2013
    Location
    Gladstone QLD AUSTRALIA
    Posts
    3,245
    Thanked: 804

    Default

    Excellent job
    Came outs awesome
    Looks near mint now
    Saved,
    to shave another day.

  13. The Following User Says Thank You to Substance For This Useful Post:

    engine46 (12-04-2014)

  14. #8
    Senior Member cubancigar2000's Avatar
    Join Date
    Dec 2013
    Location
    Idaho
    Posts
    679
    Thanked: 91

    Default

    Buffing is simple if you keep the wheel turning away from any edge. Never have it turning towards an edge - that said a dremel can be a good thing but can also be a bad thing
    engine46 likes this.
    One tired old Marine- semper fi, god bless all vets

  15. The Following User Says Thank You to cubancigar2000 For This Useful Post:

    engine46 (12-04-2014)

  16. #9
    I used Nakayamas for my house mainaman's Avatar
    Join Date
    Aug 2009
    Location
    Des Moines
    Posts
    8,664
    Thanked: 2591
    Blog Entries
    1

    Default

    Great Job.
    Dremels can be very very useful, but are very very dangerous.
    I use a magnetic jig to make things easier and safer when I use my Dremel.
    johnmrson, lz6 and engine46 like this.
    Stefan

  17. The Following 2 Users Say Thank You to mainaman For This Useful Post:

    engine46 (12-04-2014), Geezer (12-04-2014)

  18. #10
    Senior Member blabbermouth Steel's Avatar
    Join Date
    Nov 2013
    Posts
    2,321
    Thanked: 498

    Default

    Very nice! Surprising how brand new some of these old razors can look.
    engine46 likes this.
    What a curse be a dull razor; what a prideful comfort a sharp one

  19. The Following User Says Thank You to Steel For This Useful Post:

    engine46 (12-04-2014)

Page 1 of 5 12345 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •