What are you working on?

Quote:

---

Originally Posted by BeJay

Cleaning up this Otto Busch "world Master". It's got some staining and lots of little rust spots. I'm hoping to get it cleaned up without any sanding or greaseless. This Dialux Vert is an awesome compound that may be up to the task. I assume it's got lots of CroOx, but I suspect there are other abrasives in it as well. It's almost as aggressive as Emory, but leaves as nice a finish as any rouge. Its not so great for scales though.

---

From the Data Safety Sheet:

Trade name:

Unipol® Dialux green

General chemical description

mixture of fatty acids, paraffines, abrasive polishing minerals, chromoxide

After thinking about it I decided to have the writing on the box translated/it's pretty much you will find online:

The Dialux Vert is especially recommended for fine brightening with polishing, special steels, very hard alloys, chromium, cobalt chromium, platinum etc.

To be used on circular brush, felt or cotton disc.

Quote:

---

Originally Posted by BeJay

Cleaning up this Otto Busch "world Master". It's got some staining and lots of little rust spots. I'm hoping to get it cleaned up without any sanding or greaseless. This Dialux Vert is an awesome compound that may be up to the task. I assume it's got lots of CroOx, but I suspect there are other abrasives in it as well. It's almost as aggressive as Emory, but leaves as nice a finish as any rouge. Its not so great for scales though.
Attachment 257053
Attachment 257054

---

Typical age marks, but I noticed there's hardly any hone wear. Once cleaned up, it should be a looker!

Well I been busy lately and havent had tiem to do anything but decided to try and learn how to remoce scales without breakign them. All my early attempts were failures. So I just hacked away at it on some that already had broken scales. I used a small anvil with a hole in it but seems the hole was too big and I continued to break scales. Then decided to use a piece of aluminum with a hole just big enough for the pin to go through and I started to have some succes.
Attachment 257069Attachment 257070

These were all broken to some degree before I did anything
Attachment 257068

Then moved on to better ones. The last is a nice Dubl Duck Satin Edge set of scales that had that had an IROS KEEN blade in them. Managed to remove the blade without damaging the scales!
Now I just have to find a dubl duck to go inside them. Either that or trade them to someone for a different set of scales.
Attachment 257072

I learned early on that using a punch and hammer will result in busted scales most of the time.
JMHO

Quote:

---

Originally Posted by sharptonn

I learned early on that using a punch and hammer will result in busted scales most of the time.
JMHO

---

How do you do remove pins?

The Busch cleaned up pretty well. The perfectionist in me wants to go back and do some sanding but it really is pretty nice as is.
Attachment 257074

The wedge is a little piece of tubing. I've seen this on other razors and always assumed the it was added by someone that didn't have a spacer handy. These are obviously the original scale though and the factory style pins all match. Either way, it's serving its purpose and will stay in there.
Attachment 257075

Quote:

---

Originally Posted by AlanQ

How do you do remove pins?

---

Best explained here beginning with post #27; http://straightrazorpalace.com/works...le-halves.html

Quote:

---

Originally Posted by sharptonn

Best explained here beginning with post #27; http://straightrazorpalace.com/works...le-halves.html

---

my original attempts at drilling out the pins all ended in failure, think if I dimpled the crown of the pin better I might be more successful
Thanx

I find if my approach is to flatten the pin, start a hole with a split point bit in a pin vise and then use a drill press with a split point bit, all goes fairly well, most of the time.

Quote:

---

Originally Posted by AlanQ

my original attempts at drilling out the pins all ended in failure, think if I dimpled the crown of the pin better I might be more successful
Thanx

---

I use a small file to flatten and remove as much of the pin as possible and I do that on both sides as sometimes you need to 'Gently' work back and forth. I also have a pinning block that I drilled a hole completely through and then made a slight depression and that really helped!

However I now use a product that I was turned onto by a friend who lives in the boonies of Idaho. I find it of great use. However it can stain bone, Ivory and certain light colored horn.

While marketed as a 'penetrating oil' my friend referrers to it as a 'creeping oil' that is widely used in gunsmithing. It's great stuff!

Attachment 257084