Printable View
I’m always packing to go somewhere. At work right now, until the 2nd, then a boat trip to the other end of the province, then off to meet my wife at her parents place inland, and drive home. I often take my seven day roll with me. I also like to pack my panama hone, it does a nice job. I have a very nice roll made a member here,greatbolo.
Attachment 309097
The rest of the gear changes all the time but the roll always travels with me.
Mike that’s a serious challenge. I did a similar project in the early days, only I was foolish enough to try to get all the pitting out after the tumbler.
I’m not sure why cell rot occurs, Tom uses a silicone spray to keep his well coated to prevent it breaking down.
Jerry, I am looking forward to seeing the finish on those hone boxes.
Yeah, that's some pretty bad cell-rot. Good luck with it, Mike. I too look forward to seeing Jerry's latest finished boxes. I bet those Lyptus boxes smell nice being worked!Quote:
Originally Posted by RezDog
Nice roll, Shaun-And if we're showing off our "rolls," here's mine with the blades that are coming with me:
Attachment 309098
Mine is nothing fancy, but it's very sturdy and protective, with heavy canvas on the outside, and soft silicone-impregnated liner. I got it from The Superior Shave. A homemade one would be cool, though. I should ask my wife-she can sew literally anything. Hmmm, now I'm thinking again (though realistically, she'll never have time. She is also a department chair/AP teacher in the same high school as me, and is even busier than I am).
Got home in time to sand one box to 600 grit. Then I thought I'd put some Ren. Wax on the insides to protect it from whatever coatings I might put on the outside. But the color just popped out so beautifully I couldn't help myself. I just waxed the box completely. No clear finish or oils or stains. Just Wax!
Attachment 309125Attachment 309126
A before pic for comparison
Attachment 309127
Wax is a beautiful finish.
A very fine bit of work, nice fit and great grain pattern.
I've actually been working on the razor, but my vacation ended and I haven't had as much time to mess with the photos. Also had to catch up with all the great work being put up. Lots of really nice stuff, congrats to all of your fine work.:chapeau
So the Robeson...
I worked the blade a bit more with some WD40 and steel wool, got some improvement and am happy with where it's at.
As for the scales, unfortunately when I was drilling out the pins the bit slid off the pin and carved out a chunk of the bolsters. So this is now more of a learning project. So here's a few things I've learned:
Using blue painters tape to protect scales and bolsters makes it hard to see the bit wander off the pin. That left about 3/4 of the pin still in the scale so I wound up using a small ball end dremmel bit in my drill press and it worked pretty well to get the pin cut out. I'll may try that from the start on a future project.
The scales on this razor are effectively one piece, so I didn't even need to remove the rear pin :gaah:
First time straightening scales. Took me three tries with some boiling water and some carefully placed bamboo skewers and clamps to sneak up on it and get them sorted out.
Before
Attachment 309170
After
Attachment 309169
You can use wood stain to color clear epoxy and get a pretty close color match. I used some cherry and dark walnut to get close to the colors of these scales. Not perfect, but I'm not trying to make a show queen. After mixing the epoxy I let it sit for 30-45 minutes (24 hour cure time) so it thickened up and stayed in place better. Time may vary due to temp, so check on it every 10-15 minutes until it's the thickness you want.
Roughed up the damaged area with some sand paper
Attachment 309172
The repair materials (the epoxy in the mixing dish is a test batch I did to make sure it would harden)
Attachment 309171
Mixing in the color (I just added a few drops of each until I got to the color I wanted)
Attachment 309177
Got the epoxy in place and used the wax paper to help it keep shape while drying.
Attachment 309176 Attachment 309175
The repair after rough shaping
Attachment 309174
The final repair and an idea for covering the damage to the bolsters
Attachment 309173
The color of the epoxy seemed to darken a little as it dried so it's a bit off, but not bad. I could file it out and try again, but my goal is more to getting this working again.
I was thinking of gently doming some 00 wide brass washers to cover the damage when I re-pin. Is this a good idea? or would it look kinda goofy? Thanks in advance for your opinions and advice.
Nice repair. I realize it is not perfect but sometimes it’s about learning a process not achieving a seamless result. As for the pin error, they happen at times. In general I fell like I have more control holding the razor in my hand, and pushing it into the turning drill bit. Also, I check often to see hose the hole is going, and I start with making a flat spot on top of the pine with a file and then starting with a split point drill bit by hand and then moving to the drill press. I’ve made many unintentional holes over time. I think Tom is the master of careful control and drilling out pins. I bet he didn’t start there though. :-)
P.S.
You can use large washer to cover an oops, but I would think SS or NiAg would look better.
I'll try moving the pin to the bit next time. I had filed the pin flat and put a small dimple in it with a punch. Not sure why the bit walked off, just did and I didn't notice till it was too late. Even so, it's been a fun project and I'll get another razor to try in the end :D.
I think you're right about the SS or NiAg, the brass is what I had on hand.
That's very good work. I haven't done it yet but I thought I'm using the epoxy in the same way. It's helpful to see that you had good results with that and a good tip to maybe go a little lighter than you think it would need to be. I suppose you could always use a detailed brush and paint on some more dark stain if it needed to be darker. I have a Robson shuredge "The razor that fits your face" that I love. That was the first razor that I bought for myself new. Although I should say NOS. It didn't have the box but it still had the sticker on it and looked like it had been in a display case.
Shuan, that's how I take out pins almost exactly except I don't usually drill them all the way through (maybe you don't either). I usually drill them down to where The collar will come off and then try to lift the scale (gently) off of the pin if possible and then unload the washers and the blades if I can rotate the scale back away from the pin. I'm always scared to death of drifting into the scale and yet I still do it sometimes even though I'm as careful as I can be. Once I get that scale loose I'll usually either drive the pin out or pull it out with a pair of bulldog pliers.
