Page 54 of 412 FirstFirst ... 44450515253545556575864104154 ... LastLast
Threads 1061 to 1080 of 8221

Forum: The Workshop

Discuss anything having to do with cleaning, repair, and restoration of straight razors.

  1. Sticky Thread Sticky: Welcome to the Workshop: How do I / Where do I / What do I / answers are here

    Started by Bruno, 03-14-2008 05:56 PM
    • Replies: 5
    • Views: 92,296
    gssixgun
    01-06-2023, 01:32 PM Go to last post

  1. Wade and Butcher that spoke to me...

    Started by Suticat, 10-22-2015 07:00 PM
    1 Attachment(s)
    • Replies: 8
    • Views: 658
    aaron1234
    10-24-2015, 09:45 PM Go to last post

  2. Buckeye Burl

    Started by Suticat, 11-24-2015 08:07 PM
    2 Pages •
    1 2
    9 Attachment(s)
    • Replies: 11
    • Views: 1,208
    ajkenne
    12-02-2015, 02:41 AM Go to last post

  3. W&B FBU, What would you do?

    Started by Suticat, 05-12-2016 11:36 PM
    3 Pages •
    1 2 3
    7 Attachment(s)
    • Replies: 20
    • Views: 1,551
    engine46
    05-16-2016, 09:12 PM Go to last post

  4. Poll Poll: A or B?

    Started by Suticat, 05-26-2016 04:13 AM
    6 Attachment(s)
    • Replies: 9
    • Views: 646
    Suticat
    05-28-2016, 01:11 PM Go to last post

  5. Question Locating a source for replacement scales.

    Started by Sure Shot Rick, 08-31-2006 02:44 AM
    • Replies: 3
    • Views: 637
    Kees
    08-31-2006, 04:43 AM Go to last post

  6. Duble Duck Scales

    Started by Sure Shot Rick, 09-12-2006 09:21 PM
    • Replies: 2
    • Views: 679
    xman
    09-13-2006, 01:26 AM Go to last post

  7. Who are the vendors here that professionally tighten pins or rescale?

    Started by supersco, 02-05-2014 03:12 AM
    2 Pages •
    1 2
    • Replies: 16
    • Views: 1,239
    supersco
    02-20-2014, 10:29 PM Go to last post

  8. Need some advice on my first.

    Started by Superman, 02-08-2011 12:25 AM
    keen, kutter, simmons
    • Replies: 5
    • Views: 926
    Superman
    02-08-2011, 12:41 AM Go to last post

  9. Aluminium washers - a bad idea?

    Started by Superman, 02-18-2011 05:04 PM
    • Replies: 3
    • Views: 1,201
    Superman
    02-18-2011, 09:19 PM Go to last post

  10. Junk to Funk

    Started by superfly, 07-15-2005 03:05 PM
    • Replies: 4
    • Views: 1,228
    randydance062449
    07-24-2005, 04:34 AM Go to last post

  11. Bill's scales, once again :D

    Started by superfly, 04-29-2006 10:21 AM
    • Replies: 6
    • Views: 797
    Garry
    05-08-2006, 06:17 AM Go to last post

  12. can you use Rotozip bits in a Dremel tool?

    Started by superbleu, 07-13-2009 08:25 PM
    • Replies: 6
    • Views: 27,087
    the wanderer
    07-15-2009, 05:35 AM Go to last post

  13. Unpinning without damaging scales

    Started by superbleu, 12-17-2009 03:25 AM
    2 Pages •
    1 2
    • Replies: 13
    • Views: 3,882
    TheBaron
    12-18-2009, 03:37 PM Go to last post

  14. Hand sanding diminishing returns

    Started by superbleu, 11-23-2009 02:29 AM
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 13
    • Views: 1,905
    MisterLewisR
    11-24-2009, 12:56 AM Go to last post

  15. Blown temper, how hot is too hot

    Started by superbleu, 04-15-2010 06:19 PM
    • Replies: 9
    • Views: 948
    Bruce
    04-16-2010, 05:30 PM Go to last post

  16. Filling in grain/finishing Wenge

    Started by superbleu, 04-17-2010 02:01 PM
    • Replies: 7
    • Views: 4,735
    deighaingeal
    04-17-2010, 11:35 PM Go to last post

  17. First set of scales

    Started by superbleu, 04-18-2010 01:35 AM
    2 Pages •
    1 2
    9 Attachment(s)
    • Replies: 16
    • Views: 1,584
    HNSB
    04-23-2010, 05:04 PM Go to last post

  18. Micarta thickness question

    Started by superbleu, 08-07-2012 03:53 PM
    • Replies: 3
    • Views: 732
    Jimg1775
    07-14-2013, 04:49 PM Go to last post

  19. Hope you don't mind

    Started by Sunsi, 06-06-2007 09:50 AM
    4 Attachment(s)
    • Replies: 3
    • Views: 864
    C utz
    06-06-2007, 01:00 PM Go to last post

  20. Natural wook finishes

    Started by Sunsi, 06-14-2007 01:32 PM
    • Replies: 4
    • Views: 650
    Howard Newell
    06-14-2007, 03:39 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules