Results 7,901 to 7,910 of 20565
91447LikesThread: What are you working on?
LinkBack URL
About LinkBacks-
03-05-2017, 04:26 PM #7901I love Burls....... and Acrylic
- Join Date
- Mar 2012
- Location
- Baden, Ontario
- Posts
- 5,475
Thanked: 2284
You're a life saver Mike! I have a wedge Norton hone that I use for the inside face of my lathe gouges. It was pretty easy to get a good edge on that 1/16 bit, not sure why I was so lazy to do it. Just never dawned on me.
Burls, Girls, and all things that Swirl....
-
The Following User Says Thank You to HARRYWALLY For This Useful Post:
outback (03-05-2017)
-
03-05-2017, 05:11 PM #7902Senior Member
- Join Date
- Mar 2015
- Location
- Akron, Ohio
- Posts
- 12,056
Thanked: 4312
Ahhhh, nice continuous cut too. "Quote"
Originally Posted by HARRYWALLY
You're a life saver Mike! I have a wedge Norton hone that I use for the inside face of my lathe gouges. It was pretty easy to get a good edge on that 1/16 bit, not sure why I was so lazy to do it. Just never dawned on me.
I have no place for anything dull in my life. [emoji56]engine46 likes this.Mike
-
03-05-2017, 05:18 PM #7903Senior Member
- Join Date
- Mar 2015
- Location
- Akron, Ohio
- Posts
- 12,056
Thanked: 4312
Hey guys, got a question.
This Packwood I'm working on
has a pitted spine as well. Can I remove them without harm to the geometry, or would it be best to leave it be. Its not going to interfere with stropping, but I'm trying to make this one nice and clean, being I've gone this far with it already.
-
03-05-2017, 05:27 PM #7904Senior Member
- Join Date
- Jan 2012
- Location
- Waukesha, Wisconsin
- Posts
- 1,943
Thanked: 390
Should be fine, unless you're removing more steel than the hone wear
xiaotuzi likes this.
-
03-05-2017, 06:36 PM #7905Senior Member
- Join Date
- Feb 2013
- Location
- Haida Gwaii, British Columbia, Canada
- Posts
- 14,439
Thanked: 4827
Sand it off Mike, it should not go deep enough to create a separate issue.
It's not what you know, it's who you take fishing!
-
03-05-2017, 07:14 PM #7906I love Burls....... and Acrylic
- Join Date
- Mar 2012
- Location
- Baden, Ontario
- Posts
- 5,475
Thanked: 2284
Back together, let's see if I can get a bevel set yet today.
Burls, Girls, and all things that Swirl....
-
The Following User Says Thank You to HARRYWALLY For This Useful Post:
xiaotuzi (03-05-2017)
-
03-05-2017, 07:38 PM #7907Senior Member
- Join Date
- Feb 2013
- Location
- Haida Gwaii, British Columbia, Canada
- Posts
- 14,439
Thanked: 4827
I put way too much time in on this for what shows.
My Henckels display case with some of my Henckels razors.
There is a piece of sheet metal, over a piece of wood, it is covered by fabric, and magnets hold everything not quite where I put them. I will have to figure out a better mouse trap, but in the mean time this is it.It's not what you know, it's who you take fishing!
-
-
03-05-2017, 08:04 PM #7908I love Burls....... and Acrylic
- Join Date
- Mar 2012
- Location
- Baden, Ontario
- Posts
- 5,475
Thanked: 2284
I see a lot of nice razors in there Shaun!! Wonderful collection!
Burls, Girls, and all things that Swirl....
-
-
03-05-2017, 08:12 PM #7909Str8Faced Gent.
- Join Date
- Aug 2013
- Location
- Orangeville, Ontario
- Posts
- 8,449
- Blog Entries
- 1
Thanked: 4206
That came out super shaun. Terrific showcase for some stellar razors.
"Depression is just anger,, without the enthusiasm."
Steven Wright
https://mobro.co/michaelbolton65?mc=5
-
-
03-05-2017, 08:21 PM #7910Senior Member
- Join Date
- Mar 2015
- Location
- Akron, Ohio
- Posts
- 12,056
Thanked: 4312
That is a sweet collection Rez.
Just a bit envious here. [emoji54]Mike
-
Reply With Quote